SC402 Stump Cutter
- More power, more torque
- Built with features for jobsite efficiency
- Designed for serviceability
FEATURES & BENEFITS
No matching record found!
SPECIFICATIONS
General Dimensions and Weights
| Height | 53 in |
| Sound Power | 107.6 dB(A) |
| Weight - Engine Option One | 1950 lbs |
| Width | 50.1 in |
| Overall Height Transport | 53 in |
| Overall Width Transport (with duals) | 50.1 in |
| Overall Width Transport (without duals) | 35.5 in |
| Length | 118 in |
| Weight With Chip Blade Option (Additional) | 85 lbs |
Engine - Option one
| Make and Model | Briggs & Stratton Vanguard® EFI/ETC |
| Oil Filter | Spin-on |
| Clutch Type | Electric clutch with brake |
| Fuel Type | Gasoline |
| Recommended Oil | 10W30 (see engine manual) |
| Alternator | 20/50 Amp (rpm-based) |
| Maximum Angle of Continuous Operation | 25 deg |
| Oil Volume with Filter | 2.5 qt |
| Max Fuel Consumption | 2.2 gph |
| Torque (Max) | 56 ft-lb |
| Gross Horsepower (Maximum) | 40 hp |
| Cooling Medium | Air |
| Air Cleaner | Dry-type safety element and restriction indicator |
| Fuel Tank Capacity | 10 gal |
| Number of Cylinders | 2 |
Electrical System
| System Voltage | 12 V |
| Battery | 550 CCA |
| Switches | Two-speed 2x4 and 4x4 ground drive, cutterwheel engage/disengage, blade (if equipped) |
| Warning Lights | Oil pressure, engine fault, operator presence status, clutch engage/disengage status |
| Shutdown System | Engine low oil pressure will derate engine |
| Controller | Danfoss® |
Chassis
| Degree of Oscillation | 12 deg |
| Steerable Axle Type | Hydraulic steering oscillating axle |
| Control Station Description | Fixed side |
| Brake Type | Spring-applied, hydraulic release at rear motors |
| Tires - Option One | 5.7 in x 8 in (14.5 cm x 20.3 cm) dual standard |
| Axle/Suspension | Rigid/fixed (rear) |
| Fender Description | Yes |
| Toolbox Description | Standard |
| Frame Description | Welded tube and plate steel |
Cutterwheel System
| Number of Teeth | 18 |
| Chip Containment | 7.5 cu ft |
| Cutterwheel Guard | Standard |
| Reversible Pockets/Teeth | 16 |
| Tooth Description | Vermeer cutting system (VCS) |
| Cutterwheel Cut Below Ground | 15 in |
| Cutterwheel Cut Above Ground | 24 in |
| Cutterwheel Straight Line Dimension | 47 in |
| Cutterwheel Speed | 1525 rpm |
| Cutterwheel Thickness | .5 in |
| Cutterwheel Diameter without Teeth | 20 in |
Cutterwheel Drive Components
| Jackshaft Bearing Type | Sealed ball |
| Bearing Dimensions - Secondary Belt | 1.8 |
| Cutterwheel Shaft | 1.8 |
| Number of Secondary Belts | 6 banded |
| Bearing Dimensions | 1.3 bore |
| Jackshaft Dimension | 1.3 |
| Number of Primary Belts | 2 individual (matched pair) |
| Belt Type | V-belt |
Option One
| Blade Travel Below Ground | 2.5 in |
| Blade Travel Above Ground | 8 in |
| Chip Blade Dimension | 33-in wide x 12-in tall (83.8 cm x 30.5 cm) |
Hydraulic System
| Tank capacity | 6.5 gal |
| System relief pressure | 2470 psi |
| System Type | Open-loop series system |
| Recommended Oil Type | Vermeer HyPower 68 |
| Directional Control | Electric over hydraulic |
| Flow Control | SmarSweep |
| Filtration Method | 10-micron fill strainer and 6-micron return filter |
| Pump Flow at Maximum RPM | 6.2 gpm |
Ground Drive
| Low Speed Travel | 65 ft/min |
| High Speed Travel | 130 ft/min |
Cutterwheel system - Two
| Cutterwheel Diameter without Teeth | 17 in |
| Cutterwheel Thickness | .5 in |
| Cutterwheel Speed | 1525 rpm |
| Cutterwheel Straight Line Dimension | 47 in |
| Cutterwheel Cut Above Ground | 24 in |
| Cutterwheel Cut Below Ground | 15 in |
| Tooth Description | Yellow Jacket™ cutter system |
| Number of Teeth | 20 |
| Cutterwheel Guard | Standard |
| Number of Indexes | 2 |
| Number of Pockets | 20 |
| Reversible Pockets/Teeth | 20 |
| Chip Containment | 7.5 cu ft |
SEE IT IN ACTION
